通用包装 氯丁橡胶止水带施工工艺

        本通用包装类产品：通用包装 氯丁橡胶止水带施工工艺，由河北衡水市供应商河北瑞博橡塑制品有限公司供应，详细信息如下：
氯丁橡胶止水带施工工艺　 咨询热线： 131 6657 0832
The choice of the material of the water stopping belt can be made in accordance with the following provisions:
1, under normal circumstances, choose natural rubber water stop belt;
2, in case of weak acid, alkali corrosion medium, it is better to use neoprene water stop belt;
3, in case of oil medium, should choose nitrile rubber water stop belt;
4, in case of mold erosion possibility, should consider the waterproof belt mildew resistance, and its grade should reach 2 and above 2;
5, when the use temperature is: -25 degrees ~60 degrees, the use of chloroprene rubber water stop, -35 degrees ~60 degrees, the use of natural rubber water stop, -40 degrees ~60 degrees, choose three yuan ethylene propylene rubber water stop;
6, when there should be waterproof board and other materials welding, should choose the same as its molecular synthetic resin water stop belt (EVA, PE, ECB, hdpe, PVC).
氯丁橡胶止水带施工工艺
止水带材质的选择可按照下列规定：
1、一般情况下多选择天然橡胶止水带；
2、遇有弱酸、碱类腐蚀介质时，宜选用氯丁橡胶止水带；
3、遇有油类介质时宜选用丁腈橡胶止水带；
4、遇有霉菌侵蚀的可能时，应考虑止水带的防霉性，其等级应达到2级及2级以上；
5、当使用温度为：-25℃~60℃时选用氯丁橡胶止水带、-35℃~60℃时选用天然橡胶止水带、-40℃~60℃时选用三元乙丙橡胶止水带；
6、当遇有应与防水板等材料焊接时，宜选用与其同分子的合成树脂型止水带（EVA、PE、ECB、hdpe、PVC）。
橡胶止水带物理机械性能：
1、我公司生产地HD系列橡胶止水带是采用国家标准GB18173.2-2000生产的，尺寸公差技术要求一律执行国家标准。如用户有特殊要求，可按用户要求制造。
2、产品在运输及存放时，应避免阳光直射，勿与热源、油类及有害溶剂接触。勿与影响橡胶质量的物质相接触。成品应取直平放，勿加重压。存放场所*好保持-10℃～+30℃，相对湿度在40％--80％，并应保持清洁。
产品规格：
CB300×6 CB300×6 CB350×8 CP250×6 CP230×6 EB300×6 EP350×8等。
橡胶止水带的施工与安装：
止水带是在混凝土浇注过程式中部分或全部浇埋在混凝土中，混凝土中有许多尖角的石子和锐利的钢筋头，由于塑料和橡胶的撕裂强度比拉伸强低3-5倍，止水带一旦被刺破或撕裂时，不需很大外外力裂口就会扩大，所以在止水带定位和混凝土浇捣过程中，应注意定位方法和浇捣压力,以免止水带被刺破，所以在止水带定位和混凝土浇捣过程中，应注意定位方法和浇捣压力，以免止水带被刺破，影响止水效果,具体注意事项如下:
1、止水带不得长时间露天曝晒，防止雨淋，勿与污染性强的化学物质接触。
2、在运输和施工中，防止机械，钢筋损伤止水带。
3、施工过程中，止水带必须可靠固定，避免在浇注混凝土时发生位移，保证止水带在混凝土中的正确位置。
4、固定止水带的方法有：利用附加钢筋固定；*卡具固定；铅丝和模板固定等（图2），如需穿孔时，只能选在止水带的边缘安装区，不得损伤其它部分。
5、用户定货时应根据工程结构，设计图纸计算好产品长度，异型结构要有图纸说明，尽量在工厂中将止水带连接成整体，如需在现场连接时，可采用电加热板硫化粘合或冷粘接(橡胶止水带)或焊接(塑料止水带)的方法，如用户连接有困难，我公司可派技术人员现场指导。
氯丁橡胶止水带施工工艺
Rubber stop belt; physical and mechanical property:
1, our company produces HD series rubber water stop belt is the use of national standard GB18173.2-2000 production, size tolerance technical requirements are to implement national standards. If the user has special requirements, can be manufactured according to user requirements.
2, the product in transportation and storage, should avoid direct sunlight, not with the heat source, oil and harmful solvents contact. Do not contact substances that affect the quality of the rubber. The finished product should be taken straight and flat, without heavy pressure. Storage sites should be kept from -10 to +30 centigrade with relative humidity at 40％--80％ and should be kept clean.
Product specification:
CB300 x 6 CB300 x 6 CB350 x 8 CP250 x 6 CP230 * 6 EB300 * 6 EP350 * 8 etc..
Construction and installation of rubber water stop:
The waterstop is in the concrete pouring process in all or part of pouring buried in concrete, there are many sharp stones and sharp head reinforced concrete, the tear strength of rubber and plastic tensile and low 3-5 times, once the waterstop punctured or torn, without external force gap will expand, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as to avoid the water stop was punctured, so in the waterstop positioning and concrete pouring process, should pay attention to positioning method and pouring pressure, so as to avoid the water stop is punctured, influence the sealing effect, the specific considerations are as follows:
1. The water stop belt shall not be exposed to the outside for a long time to prevent rain, and do not touch with the polluting chemicals.
2, in transportation and construction, to prevent mechanical, steel damage, water stop.
3. During construction, the water stop belt must be reliably fixed to avoid displacement during pouring concrete and to ensure the correct position of the stop belt in concrete.
Method 4, fixed strip: the use of additional reinforcement fixation; special fixture fixed; the wire and fixed template (Figure 2), such as perforation, can only choose the installation area on the strip edge, not to damage other parts.
5, the user order should be based on the engineering structure design drawings, calculate the length of products, have special structure drawings and specifications, try to connect into a whole band in the factory will stop, if necessary in the field of connection, can use electric heating plate vulcanization bonding or cold bonding (rubber waterstop) or welding (plastic waterstop). Methods, such as the user is connected with the difficulties, our company can send technical personnel on-site guidance.
关键词：通用包装 通用包装 氯丁橡胶止水带施工工艺 河北瑞博橡塑制品有限公司